What Would You Light Today!? TM

(818) 772-1900

Customer Service/Sales
0 items(s) Sub Total: $0.00 cart

(818) 772-1900

DEALER LOCATOR

Frequently Asked Questions #

Frequently Asked Questions

 


  1. Should I get White or Multicolor?
  2. Do you provide installation services? 
  3. My need is not cabinet lighting. Can you help? 
  4. I have the kitchen blueprint. Can you work with that? 
  5. We are doing a remodel. Is it better to contact you before the project starts or after it is finished?
  6. What does it cost to get your consultation help? 
  7. I have a small kitchen. Can you do small custom projects?
  8. Do custom setups cost more? 
  9. I have 3 sections of upper cabinets that are not connected. How do I run wires from one to another? 
  10. Last thing I want to do is drill holes in my new cabinets. Can you help? 
  11. The issue I have is that I have 3 banks of cabinets, one aprox 6ft, one aprox. 8ft and one aprox 7 ft that I need to light. They are on 3 separate walls and there is really no way to run a cord to connect any of them. I have power at each wall, and all three are connected to the same wall switch. How can I install these lights and have all three sets work in unison? I don’t want to have to use 3 separate remotes. Is there a way to get 3 responders that are all programed to the same remote frequency or is there another way to make this work? 

1. Should I get White or Multicolor?


If you are not intending to use the multicolor functions then staying with white simplifies the installation and offers a more accurate “warm” white light. White systems are normally less expensive as well. If you have your heart set on color contrasts an alternative option may be to keep white lights for undercabinet and add multicolor lights in the toe kick, or above cabinets if they do not reach the ceiling. You will be creating a stunning effect by having white lights on the countertop and contrasting colors above projecting on the ceiling and down low shining on the floor.


2. Do you provide installation services? 


Cyron has experts on staff that would perform the lighting installations within a 20 miles radius of our headquarters.


3. My need is not cabinet lighting. Can you help? 


Yes, you would be surprised of find out about our capabilities.

 

4. I have the kitchen blueprint. Can you work with that? 


Certainly! We prefer blue prints, layouts, sketches, pictures, videos. Anything that can describe the project. Describing system layout over a phone conversation normally take too long and still leave much to misunderstand. 


5. We are doing a remodel. Is it better to contact you before the project starts or after it is finished?


The earlier you contact our staff the easier implementation will be.


6. What does it cost to get your consultation help? 


Normally nothing at all. Costs will incur if we must create elaborate sketches and designs.

 

7. I have a small kitchen. Can you do small custom projects?


No project is too small.


8. Do custom setups cost more? 


Not necessarily. Often times custom setups can save costs by saving installation time on the field. We can custom make lights much quicker and more efficiently than you or your contractor.


9. I have 3 sections of upper cabinets that are not connected. How do I run wires from one to another? 


You may not need to. Creating 3 zones of light that can be all controlled by a wifi or infrared signal can make all three cabinets to synchronize. You will however need power at each zone.


10. Last thing I want to do is drill holes in my new cabinets. Can you help? 


Yes, we can help! All Cyron lights can also be mounted with heavy grade 2-sided tape. CLS and HTP systems include the tapes. 


11. I am interested in purchasing your Cyron RGB Led under counter cabinet dimmable multicolor light kit for my kitchen. The issue I have is that I have 3 banks of cabinets, one aprox 6ft, one aprox. 8ft and one aprox 7 ft that I need to light. They are on 3 separate walls and there is really no way to run a cord to connect any of them. I have power at each wall, and all three are connected to the same wall switch. How can I install these lights and have all three sets work in unison? I don’t want to have to use 3 separate remotes. Is there a way to get 3 responders that are all programed to the same remote frequency or is there another way to make this work? 


? It is very possible to do this. You will need a controller and power supply for each of the 3 "zones". The controllers will be set to auto-on feature which means they will turn on automatically to the last color you left them before you turned off with your wall switch. One handheld remote can let you adjust all three controllers when you want to change colors or apply any other functions. If it is one of our IR remotes, you will have to point the remote in the general direction of the IR sensor of each controller. If you opt for the Wifi controller then you can control all by your phone or your smart speaker such as Alexa. 



has experts on staff that would perform the lighting installations within a 20 miles radius of our headquarters.


Yes, you would be surprised of find out about our capabilities.



If you are looking for a simple plugin system that can be installed in less than 5 minutes this is the right choice. You don’t even need to put any screws in your cabinets. You do want to make sure there is an outlet near by to plug in.


CLS systems more of a standalone light. You need to turn every light on by its own touch switch. Cannot be controlled from a remote switch.


It takes some planning (this is where Cyron’s help comes in) and a bit of do-it-yourself expertise. Wires may need to be stripped and holes drilled for a neat routing of wires through cabinetry. The end results make it worth the efforts.


Most white light systems are offered in degrees of white tones. Most likely you want to stay away from RGB multicolor.


has been in the forefront of zero glare movement for over a decade, even when everyone thought dots are cool. CLS and couple of CB series models are specifically designed with zero-glare in mind.


In general all RGB multicolor lights can only be dimmed with its own controller, not a traditional wall dimmer. CLS systems only dim with their own switch. CB series can be purchased with the optional dimmable drivers.


The earlier you contact our staff the easier implementation will be.


Not necessarily. Often times custom setups can save costs by saving installation time on the field. We can custom make lights much quicker and more efficiently than you or your contractor.


You may not need to. Creating 3 zones of light that can be all controlled by a wifi or infrared signal can make all three cabinets to synchronize. You will however need power at each zone.


Yes, we can help! All Cyron lights can also be mounted with heavy grade 2-sided tape. CLS and HTP systems include the tapes.



If you are looking for a simple plugin system that can be installed in less than 5 minutes this is the right choice. You don’t even need to put any screws in your cabinets. You do want to make sure there is an outlet near by to plug in.


CLS systems more of a standalone light. You need to turn every light on by its own touch switch. Cannot be controlled from a remote switch.


It takes some planning (this is where Cyron’s help comes in) and a bit of do-it-yourself expertise. Wires may need to be stripped and holes drilled for a neat routing of wires through cabinetry. The end results make it worth the efforts.


Most white light systems are offered in degrees of white tones. Most likely you want to stay away from RGB multicolor.


has been in the forefront of zero glare movement for over a decade, even when everyone thought dots are cool. CLS and couple of CB series models are specifically designed with zero-glare in mind.


In general all RGB multicolor lights can only be dimmed with its own controller, not a traditional wall dimmer. CLS systems only dim with their own switch. CB series can be purchased with the optional dimmable drivers.


The earlier you contact our staff the easier implementation will be.


Not necessarily. Often times custom setups can save costs by saving installation time on the field. We can custom make lights much quicker and more efficiently than you or your contractor.


You may not need to. Creating 3 zones of light that can be all controlled by a wifi or infrared signal can make all three cabinets to synchronize. You will however need power at each zone.


Yes, we can help! All Cyron lights can also be mounted with heavy grade 2-sided tape. CLS and HTP systems include the tapes.

Loading...